The Holosun EPS Carry Red Dot is a popular choice for concealed carry applications due to its small size, bright reticle, and rugged construction. However, like all electronic devices, it may sometimes require a factory reset to address any unexpected issues. This manual will walk you through the steps of resetting your Holosun EPS Carry Red Dot to its default settings.
For begin, ensure your red dot sight is turned off.
- Locate the small reset button on the side or bottom of the sight.
- Use a small, pointed object, such as a paperclip or a thin screwdriver, to press and hold the reset button for approximately 5 seconds.
- The sight will vibrate briefly to signal that the reset is complete.
Once the reset process is finished, switch your red dot sight back on. The reticle should now be at its default brightness and settings. Refer to the user manual for specific instructions on adjusting the settings to your preference.
Modifying Your Holosun EPS Carry to Default Settings
Should you need to take back your Holosun EPS Carry to its original settings, the process is fairly easy. First, find the two miniature adjustment screws on the bottom of the sight. Then, using a small screwdriver, gradually turn each screw in reverse until you arrive at the desired setting. The Holosun's instructions will specify the exact number of turns needed to reset to the default settings.
Restore Your Holosun EPS Carry to Factory Defaults
If you've been experimenting with your Holosun EPS Carry's settings and want to begin anew, returning it to the factory defaults is a simple process. This will erase all of your customized configurations and restore the sight to its initial parameters. To do this, you'll need to find the reset button on the sight and follow the manufacturer's instructions. Be guaranteed to consult your Holosun EPS Carry's manual for specific details on how to perform a factory default reset.
Performing a Factory Reset on the Holosun EPS Carry {
The Holosun EPS Carry is a popular red dot sight known for its reliability and durability. Occasionally, you might need to reset your Holosun EPS Carry to its factory settings. This can be helpful if you're experiencing issues with the sight or simply want to start fresh.
Here's a step-by-step guide on how to conduct a factory reset on your Holosun EPS Carry:
- Make sure the sight is powered down.
- Find the reset button on the rear of the sight. It's a small, recessed button.
- Apply a thin, pointed object, such as a paper clip or a screwdriver, to press the reset button. Hold it down for approximately 5 seconds.
- You should observe a rapid flashing light sequence on the sight's display. This indicates that the reset process is in progress.
- Release the reset button and wait for the sight to start up normally.
Your Holosun EPS Carry has now been reset to its factory settings. You will need to re-enter any customizations or adjustments you previously made.
Reset Your Holosun for Your Holosun EPS Carry
Need click here to recalibrate your Holosun EPS Carry? Performing a factory reset is an easy way to bring back it to its original settings.
This process can be helpful if you're experiencing problems with your sight or simply want to start fresh. Here's a simple guide on how to execute a factory reset on your Holosun EPS Carry:
- First, turn on your Holosun EPS Carry.
- Next, locate and press the reset button. Hold it down for about 5 seconds.
- You'll see a message on the display indicating that a factory reset is in progress.
- Wait until the message disappears and your Holosun EPS Carry powers off and back on.
Your Holosun EPS Carry is now fully restored. You can now adjust it according to your preferences.
Accessing the Holosun EPS Carry: A Factory Reset Tutorial
Looking to restore your Holosun EPS Carry sight back to its original settings? You've come to the right place. This guide will walk you through a simple factory reset process, enabling you to troubleshoot any potential concerns and ensure your sight is functioning at its best.
- Firstly locating the miniature reset button on the rear of your Holosun EPS Carry sight. You'll need a thin object, such as a paperclip, to press this button.
- As you are holding down the reset button, simultaneously power on your sight. You should see the indicator flicker a few times, indicating that the factory reset is in progress.
- Maintain holding down the button for roughly 5 seconds. Then release of the button and observe your sight. It should now be reinitialized to its factory settings.
Now, you can modify your Holosun EPS Carry's options according to your preferences. Your sight is now ready for optimal performance.